Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hp-procurve]

ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.

146 questions
1
vote
1 answer

HP Radio Port 210 web configuration

We acquired used WiFi system to provide better wlan for the customers in our hostel. The switch is HP PROCURVE 5406zl and we have 50 or so HP PROCURVE RADIO PORT 210 access points. I set up the switch and connected a few ap's; pfSense DHCP gives IPs…
J. Tamminen
  • 11
  • 3
1
vote
1 answer

HP ProCurve Vlan Isolation

Okay, so we have an HP ProCurve Switch 2824, a Zyxel router and a bunch of 2012 R2 servers. We currently have 3 VLANs in our network: 10(Public),20(Private) and 30(Management), but we'd like to have more isolation in these VLANs. I've been searching…
Niklas Lindgren
  • 58
  • 6
1
vote
3 answers

Route Subnet to only access 1 IP address on different VLAN HP Procurve

I'm trying to route VLAN 300 which has a subnet 192.168.100.0/26 to only access 10.220.1.10 on VLAN 220 but struggling with the config. HP's documentation from what I can tell just wants me to enable IP RIP but that gives access to the entire 220…
Matt Weick
  • 185
  • 1
  • 8
1
vote
1 answer

Private VLANs/Port Isolation on HP ProCurve 2524

I am trying to set up Private VLANs (as described on Wikipedia) on a HP ProCurve 2524, but I can't find any references to it in the online manual. Searching the internet hasn't yielded much either (my google-fu is weak here) though I've found some…
Morten Siebuhr
  • 639
  • 1
  • 6
  • 16
1
vote
1 answer

ProCurve Trunking

We have 3 switches at the moment - see the diagram below for NOW. Essentially the CORE switch is 7, and 8 and 9 have a 3 cable trunk each to 7. Now, we want to add Switch 5 to the equation - see AFTER - would this be a suitable way of configuring…
PnP
  • 1,684
  • 8
  • 39
  • 65
1
vote
1 answer

pfSense routing between subnets behind OPT1 and LAN

pfSense short config summary: WAN interface is on a registered Internet block of addresses connected to ISP via fibre LAN interface has IP address 10.200.1.3/24 OPT1 interface has IP address 192.168.184.1/24 A separate wireless network exists…
ChrisNZ
  • 606
  • 2
  • 9
  • 25
1
vote
1 answer

HP Procurve 2610 vlan routing

Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a…
user19039
1
vote
2 answers

Deleting the default vlan on HP Procurve 5406 switch

I´ve tried to delete the default vlan on the switch multiple times, via CLI and using the menu options by Telnet, but it keep showing the message= "The default VLAN cannot be deleted". There are no ports assigned on that vlan. ¿Is there a way to…
JmonkG
  • 23
  • 1
  • 3
1
vote
1 answer

LACP : Cisco ASA 5515 & Switch ProCurve 2920

I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created…
user979276
  • 11
  • 2
1
vote
0 answers

Windows 2012 to HP Procurve redundancy across multiple switches - multi-switch LACP?

We are looking to have our Windows 2012 server(s) connected to two separate switches, so that if one switch goes down the server(s) can still be accessed on the same IP address from the switch that is still alive. I understand from here that LACP…
morleyc
  • 1,150
  • 13
  • 47
  • 89
1
vote
1 answer

Default Gateway in a VLAN

Could I have a router/firewall device providing WAN connectivity, part of a VLAN on a switch? For example: 2, L3 Switches. 2 VLANs DefaultVLAN 10.1.1.0/24 VLAN100 192.168.1.0/24 Two Internet lines - irrelevant what they are. Both controlled…
PnP
  • 1,684
  • 8
  • 39
  • 65
1
vote
2 answers

Getting invalid input error on procurve 2510 when setting up ip helper-address

I have 3 HP Procurve 2510G-48 and I want to setup a VLAN for public wifi (VLAN100). Originally I just had the default vlan1. I have computers communicating across switches on VLAN100 with static IP addresses just fine. The problem is getting DHCP…
Jason
  • 317
  • 1
  • 6
  • 17
1
vote
2 answers

Assign all VLANs on a same port on HP procurve switch

i'm looking for this information for a few hours on the web but i still can't find the answer. I have a few HP2610 switches (no stacked) and i want to assign all VLANs to switches interconnection ports. That means that i want all my number 23 ports…
Alex T.
  • 185
  • 2
  • 12
1
vote
1 answer

How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

As you can see from my question, I have a VLAN configuration problem with a ProCurve 3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different…
ArgisIsland
  • 153
  • 1
  • 6
1
vote
3 answers

Multiple VLAN on one switch port

I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other…
Darbio
  • 557
  • 1
  • 5
  • 15
1 2 3
…
9 10