ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.
Questions tagged [hp-procurve]
146 questions
0
votes
1 answer
Fortigate + HP ProCurve Load Balancing
I have a FortiGate 100D + HP ProCurve 2824 linked together by 4x 1Gb links.
The ProCurve is configured to have ports 21-24 trunked together and load balance them.
The 4 cables from these ports are then fed into the 100D on ports 1-4 which are…
Myles Gray
- 659
- 4
- 12
- 33
0
votes
1 answer
Tagged VLAN with Procurve switch and RHEL is not working as expected
I want to configure tagged VLAN on RHEL6 where the ethernet switch involved is a ProCurve one. Now what I did is:
I created VLAN interfaces eth0.1001 and eth0.1002 on RHEL6 for server1 and VLAN interface eth0.1001 on RHEL6 in…
user1539343
- 101
- 1
- 3
0
votes
2 answers
Remove a port from a VLAN (HP ProCurve)
I'm not too familiar with switches but I want to remove port 6 from the following 'VLAN 12' I've tried searching for an easy explanation to no avail - How do I do this please?
Port Information Mode Unknown VLAN Status
---------------- --------…
sixnumber
- 55
- 1
- 2
- 8
0
votes
1 answer
HP E3800 series Web GUI times out
I am having some trouble with the web interface for my new E3800 (3800-48G-4SFP+ Switch (J9576A)). I have two of them stacked in a ring topology. When I restore to the factory default and add an IP address for my LAN to the DEFAULT_VLAN. I can…
user67572
- 23
- 2
- 6
0
votes
2 answers
How to use a MIB file
I have a HP 2626 switch and want to monitor it by SNMP. how can i use the MIB file.
Any starting points on how to understand it ?
using snmpwalk to get the data in a *nix machine and output it in a .txt file
How can i get a list of all the connected…
s.mihai
- 1,511
- 6
- 24
- 27
0
votes
1 answer
HP MSM410 WAP Wireless security mode: restrict to default gateway or off?
I have an HP MSM410 wireless access point and when I first configured it I couldn't access any other devices on the network, but I could access the internet fine. I figured out that this was because the wireless security mode was restricting…
vfilby
- 177
- 2
- 3
- 9
0
votes
2 answers
Autonegotiate errors between HP and Cisco hardware?
This is a bit of a specific extension to this question.
I've got two ASA's that feed into a Procurve switch, and then into an IPS. All is well except that the procurve absolutely refuses to autonegotiate with the ASA's...The asa's run 100full, and…
Satanicpuppy
- 5,946
- 1
- 17
- 18
0
votes
1 answer
HP ComWare - Detecting mac/hardware address of CONNECTED interface
Alright, so I'm adding an IRF member to our switch stack.
They are 5130's, JG937A.
Only problem is the IRF cables are BURIED in the rack channel (I mean buried buried), and there's no way for me to look at the switches and tell which 10GBX…
boog
- 220
- 3
- 11
-2
votes
2 answers
VLAN routing issue
I have HP Procurve Switch 2910AL-24G.
Please see attached configuration.
Client inst2is01 (10.247.167.80) and VLAN ID is 37
Server ILO (Management Port) IP : 10.247.172.70 and VLAn ID is 54
From the client inst2is01>> I can't do ssh to Server ILO IP…
user117140
- 9
- 1
- 1
- 6
-2
votes
1 answer
Is there any cheap way to convert from CX4 to RJ45?
I have an HP ProCurve 2900 with 2 x CX4 10Gb ports in the back.
And I want to somehow link it with my internet provider 10Gb hub, which only has a 10Gb RJ45 connector.
So far I was only able to find on Google, CX4 to CX4 cables, or 10Gb CX4 network…
Yonoss
- 137
- 5
-4
votes
1 answer
use HP Procurve switch 5400zl as router between 2 networks
I have a this network to explain :
--------------------- -----------------------------
| HP Procurve Switch | (A25) <----------> (Fa0/0) | Cisco Router As VPN-Router |
--------------------- …
blacksadangel
- 1
- 1