Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hp-procurve]

ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.

146 questions
1
vote
1 answer

Routing through a 2nd network with a Procurve 2848

I've got an old Procurve 2848 sat in the office I'm trying to figure out and struggling with. I'm trying to setup a route through to my other network & out to the internet. I have a Cisco managed router providing DHCP services on my office network…
Tom Barber
  • 11
  • 2
1
vote
1 answer

HP Procurve STP Path Blocking

I have four Switches that are interconnected with each other, witch form a loop as shown in this network diagram The switch 1 is the root bridge and is connected to the primary edge router. The switch 2 is the failover root bridge and is connected…
Skanderbeg
  • 15
  • 4
1
vote
0 answers

hp 2920 stack hot swap

I have 4x HP/Aruba 2920s configured in a stack using the dedicated stack hardware and cabling. All seems to be working well except for one issue: On the first unit which is acting as the "commander", the 4x dual personality ports work for both…
David Myers
  • 11
  • 1
1
vote
1 answer

How do I enable the WIFI radio of an HP ProCurve 420ww Access Point?

So based on this old question of mine I figured out that I can reset the access point and access it using telnet through a wired Ethernet connection. I have set a new password, I have set up the Ethernet connection so it doesn't conflict with my…
Torben Gundtofte-Bruun
  • 1,174
  • 2
  • 10
  • 16
1
vote
2 answers

Using a modern browser with the HP Wireless Access Point 420 (J8131A)?

I have a HP Wireless Access Point 420 (J8131A) and I am facing the problem that its admin interface uses either an ActiveX plugin or a JAR file - I'm not sure because none of browsers on none of my machines can load it. Even on Windows + Internet…
Torben Gundtofte-Bruun
  • 1,174
  • 2
  • 10
  • 16
1
vote
3 answers

Configuring a switch with WAN and LAN

I'm currently configuring a network switch (an HP procurve-8212) from scratch. To start off, I'm trying to configure a simple LAN and WAN connection. I have an Internet provider that provides me with a Gateway I can use for WAN access. So I'm a bit…
Siler
  • 349
  • 1
  • 7
  • 14
1
vote
0 answers

ProCurve 2910 - ping lost on tagging

I can't figure this out. I have 2 HP 2910 switches, interlinked (A1). VLAN 113 is management, I have an uplink to the core switch on port 20. Pinging and browsing works fine. However, I can't ping a storage device in VLAN 114. Other connected…
jbostoen
  • 41
  • 5
1
vote
1 answer

HP ProCurve, tagged, untagged, trunking?

I was configuring a pair of HP ProCurve 2530 switches last night and was created VLAN's. I created 4 VLAN's that I'm going to tag for port 24 where the switches will connect to each other. However, I'm a little confused. On port 24, I went ahead and…
Sokel
  • 291
  • 2
  • 6
1
vote
1 answer

Procurve Inter VLAN Routing

I have a VLAN routing issue on our network. We have two ProCurve 5406zl's being used as our core switches, each vlan on these switches has an IP address and VRRP is configured on each vlan for redundancy. I have enabled IP routing and Inter VLAN…
Ben White
  • 11
  • 1
1
vote
0 answers

Losing connection to devices over the weekend

We have a networking scheme such as: 10.1.0.0/16 10.2.0.0/16 10.3.0.0/16 Each network is associated with a switch. Each switch connects to a layer 3 core switch that also acts as our router. We have a plotter on the 10.1.0.0/16 network. It is…
Philosophene
  • 202
  • 1
  • 12
1
vote
1 answer

Two stacked HP 2900-48G switches. Now I need a couple SFP+ ports, possible?

I have two stacked HP 2900-48G switches in rack A. Now in rack B I need a switch that provides at least two SFP+ ports (for two servers) and at the same time establish a 10G link to the switches in rack A. Is that even possible? I don't know if…
Jorne
  • 123
  • 1
  • 6
1
vote
0 answers

Spanning Tree Protocol on HP5406zl and Netgear edge switches

I have a simple star network setup, a core HP switch with servers and storage, and WAN uplinks on it, and then trunked 2 x 1GB uplinks to some crappy old Netgear switches (I know, but moving on). We recently had a network storm. After some…
SteveDolphin23
  • 11
  • 1
1
vote
1 answer

Internet bandwidth split with HP1810-8G, using "DSCP QoS policies" and VLANs

I have the following scenario: We are a small company (~10 clients) with little resources and we rented out office space to another company(<5 clients). We ordered a 20 Mbit fiber connection which will give us Internet out of the modem via 1…
Flo
  • 11
  • 2
1
vote
0 answers

HP ProCurve 4208vl - Show PSU information?

I'm working with a few older HP ProCurve 4200-series chassis switches (4204vl and 4208vl). Some of these units have single power supplies, while others have dual power supplies. I'm trying to inventory the switch configurations, but the devices are…
ewwhite
  • 197,159
  • 92
  • 443
  • 809
1
vote
0 answers

VLAN configuration on HP J9279A

I've tried to set up separate VLAN for lab environment on one of my HP switches (J9279A/J9280A). Network schema: WAN | GW | port1 …
user273408
  • 11
  • 2
1 2 3
…
9 10