Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hp-procurve]

ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.

146 questions
1
vote
0 answers

HP Procurve 2910AL allow traffic from VLAN to VLAN

We are trying to setup so that the switch handel routing and communication between a few vlans. And then have a link network up to the fw. Here is the config: Running configuration: ; J9145A Configuration Editor; Created on release…
WebFooL
  • 51
  • 1
  • 6
1
vote
3 answers

Fibre (Fiber) Optic - Mixing SFP's and Switches

My generic question is: Can you mix switches on the opposite sides of a fibre link, or more accurately different manufactuors tranceivers. We just bought several new HP ProCurve v1810 series switches (J9450A and J9660A) and the correct HP fibre…
HaydnWVN
  • 415
  • 2
  • 8
  • 27
1
vote
1 answer

HP Procurve to Cisco - QOS

I have a HP Procurve with the following: vlan 4 name "Phones" untagged 20 ip address 10.50.60.1 255.255.252.0 qos dscp 101110 qos device-priority 10.50.100.10 dscp 101110 qos device-priority 10.50.20.38 dscp 100010 qos…
Magd
  • 169
  • 3
  • 9
1
vote
0 answers

Where is HP Procurve route type "ICMP" coming from?

I've got the following test network: Architecture: edge_a: 192.168.e.1 [edge vlan] (edge switch, no acl) [admin vlan] 192.168.m.1/24 core: 192.168.m.2/24 [admin vlan] (core router, yes acl) [admin vlan] edge_b: 192.168.m.3/24 [admin vlan]…
Shaun
  • 31
  • 2
1
vote
1 answer

Spanning tree problems in a shared HP ProCurve environment

we're sharing a server room with another company, including the network infrastructure. All the switches are HP ProCurve, in various models depending on port need and so on. We're using VLANs to separate traffic to various virtual servers Problem…
Vegar Nilsen
  • 163
  • 2
  • 5
1
vote
0 answers

HP ProCurve & Cisco switches interoperability

I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below there are some details of my configuration: #…
Kamil Z
  • 177
  • 1
  • 7
1
vote
3 answers

Cisco Catalyst VTP to HP ProCurve GARP?

I have two L3 capable ProCurve switches (2810-24G) which I would like to use in our Cisco environment. The Cisco switcheshave vtp configured, and all VLANs are added/maintained basically on the distribution switch. Is it possible to distribute what…
3molo
  • 4,330
  • 5
  • 32
  • 46
1
vote
0 answers

Load-balancing between a Procurve switch and a server

I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve…
vlad
  • 111
  • 4
1
vote
1 answer

Procurve Switch Multiple Gateways

I have a Procurve 3500yl switch that is currently handling all of the VLANs and the default gateway for my network. Currently, the gateway is set to our old FreeBSD firewall/router and I am trying to switch the traffic to our new Cisco router. I…
user49349
  • 101
  • 2
  • 6
1
vote
1 answer

Is it possible to change the voltage on a single port on an HP ProCurve 2910al POE switch and how?

I have a couple of HP ProCurve 2910al POE+ switches at my company that we are primarily using to power our VOIP phones that run on 48V DC. However, I have one wireless access point that I need to run off of POE, but it has to be 24V DC. I'm afraid…
goodman
  • 219
  • 1
  • 4
  • 8
1
vote
2 answers

Using a Level 2 switch as a core switch

I have a small user base of about 20 people on at a time and spiking up to about 80 people during peak times. Most people (80+%) are connected over our Aruba managed wireless system. We have a Windows Domain. We have 3 24-Port switches all…
imtech
1
vote
1 answer

Incorporating a DMZ within a multiple VLAN setup built around a HP Procurve 2824 switch

I am a n00b to networking and I need help trying to figure out the steps I need to setup my topology. I have the following requirements: (1) A Secure VPN which will be my Primary LAN network where all traffic which exits is encrypted via OpenVPN and…
Paul Ryan
  • 13
  • 3
1
vote
2 answers

IRF (stacking) Configuration on HP Comware switches (5130's)

I currently have a stack of 6 HP 5130's and would like to add another switch to that IRF stack. I have everything on the same firmware, etc. but I'm confused as to when to enter the configurations on the new stack member switch- before or after…
b00g3r
  • 23
  • 4
1
vote
2 answers

LAN Design Question with HP Procurve

HP Procurve 2510G-24 x 2 Port (For Servers) and 2 x HP Procurve 2510-48 Port 10/100 (For Desktops). Topology is like : Patching is terminated on 2nd floor and the servers are located on the 1st Floor. Basically the servers are connected on the wall…
Mutahir
  • 2,357
  • 2
  • 32
  • 42
0
votes
1 answer

Tagged ports on HP switch VLANs

wondering if somebody more experienced with HP procurve switching equipment can answer a pretty basic question for me. I'm trying to segment off 3 ports onto their own little network segment. I configured a vlan, made the 3 ports access ports to…
d34db33f
  • 98
  • 1
  • 8
1 2 3
…
9 10