Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hp-procurve]

ProCurve was the trade name of network products developed by Hewlett-Packard from 1998 to 2010. Since 2010 the brand name changed to HP Networking Products but users still recognize them as ProCurve.

146 questions
2
votes
1 answer

VLAN Gateways and Routing

This for hypothetical purposes - more of a learning question than an production question. If I have switch (Layer 3, lets say a Procurve) with a handful of VLAN's configured. Lets say: DEFAULT VLAN 10.1.1.0/24 VLAN10 172.16.30.0/24 VLAN100 …
PnP
  • 1,684
  • 8
  • 39
  • 65
2
votes
1 answer

Configuring VLAN's on two HP procurve switches

Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this…
pan
2
votes
1 answer

Procurve VLAN configuration

I have two ProCurve 1800-24G J9028B linked toghether by a fiber channel on ports n.23. I want an ethernet port (ex. port 21 of switch n1) to be isolated from all the others except of one of the other switch (ex. port 21 of switch n2). How to setup…
Tobia
  • 1,272
  • 9
  • 41
  • 81
2
votes
1 answer

Setup VLAN agnostic ports on HP ProCurve 1810G (Ingress Filter, Trunking)

I am wondering if it is possible to configure some ports of the web managed ProCurve Switch 1810G to participate in all VLAN traffic. Even if no VLAN with that ID has been set up inside the switch. Scenario The issue is that I have two…
Roman
  • 392
  • 1
  • 7
  • 20
2
votes
2 answers

Is the HP ProCurve 1800-24G Switch fanless or not?

Does the HP ProCurve 1800-24G Switch have a fan or not? The specs say that it does not have a fan, and so do many references I can see on the web. However, a person who is offering to sell me a used one is insisting that it does have a fan,…
paradroid
  • 868
  • 5
  • 15
  • 29
2
votes
3 answers

ProCurve ACL to prevent a subnet from leaving the switch

I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the…
user62491
2
votes
2 answers

VLAN security on HP ProCurve 1810G-24?

I'm looking into the managed switch HP ProCurve 1810G-24 to see if it can meet our office demands. The specs say it has IEEE802.1Q - whatever that means. Our office consists of four companies that share a common broadband connection. The…
Vincent
  • 23
  • 1
  • 3
2
votes
2 answers

Adding second HP 2410G-24 Switch

We have a single HP Procurve 2410G-24 Switch. For the sake of simplicity, there are 2 VLANS configured, and the ports are roughly equally split between them. VLAN1 (LAN) is for server LAN connections, VLAN (SAN) is for an iSCSI SAN. All works fine,…
user112448
  • 21
  • 1
2
votes
3 answers

Cisco 4900M trunk to HP ProCurve switch. Will this setup work?

As I previously ran a Cisco only shop I'm not sure if this is going to work. On paper it looks OK, but you never know. Will it work ? Are there special considerations that I need to be concerned about ? I've got the following situation to deal…
Tonny
  • 6,332
  • 1
  • 18
  • 31
2
votes
1 answer

Procurve 5400 10GB

I need some help for 10GB connection. I actually have a Procurve 5400zl series with some port SFP+ on V2 version module. We desperately need to connect a server with pci-x slot. what can I do to have a 10gb link? If possible I'd like to use…
Danil74
  • 21
  • 1
2
votes
1 answer

Wifi hosts can't contact one another (but wired hosts on the same vlan can)

Our current network is vlan'd, and the wifi network is on its own separate vlan (130). To connect to the 130 vlan, you connect to the access point (a HP MSM310), which is connected to an HP Procurve 2510-48G switch. In order to do some testing, a…
s3krit
  • 23
  • 3
2
votes
1 answer

HP switch 'mirror port' makes a Cisco switch port err-disabled due to keepalive loop-back

I'm trying to connect an HP ProCurve 5304xl switch to a Cisco 2950. The HP port I'm connecting to is described as a 'mirror port', which appears to be like a SPAN port except that it also allows ingress traffic. What I want is to push the traffic…
Matt Bennett
  • 143
  • 7
2
votes
1 answer

Bonding NICs with Procurve 1400-24G switch

I was looking to bond two or three NICs together to increase throughput. Now, this should be straight forward if done computer to computer, but since there are 3 computers involved which require higher bandwidth, I was going to put them into a a HP…
Charles Darke
  • 133
  • 3
1
vote
1 answer

LACP vs HP Trunk

Question on the performance and function of LACP vs HP "Trunk". Example, I have two HP 2910al-48G switches connected via two runs of CAT6 cable. Is there any difference in performance between setting up the link as LACP vs Trunk? Second and related…
JPoole
  • 125
  • 4
1
vote
2 answers

ProCurve Switch 5406zl isolate VLAN for web hosting

Need to host company website in internal network using existing hardware. Still learning how to do things... All VLAN's can talk to each other. How can I isolate VLAN250 from the rest of the network so that VLAN250 that the company website will be…
Omar
  • 111
  • 2
1 2 3
…
9 10