Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [lsi]

LSI is a manufacturer of enterprise storage and networking components.

LSI is a manufacturer of enterprise storage and networking components.

250 questions
0
votes
1 answer

Increase hardware RAID1 volume size

We are working with an IBM server and a SAS1064ET hardware RAID controller. We used two 73.4 GB 10k SAS HDDs with RAID1. As we wanted to upgrade the storage, we replaced one after another with a 600GB HDD and always waited until the RAID1 has been…
mapf
  • 101
  • 4
0
votes
1 answer

Flashing (R530 onboard) Dell PERC H730 mini to IT mode?

Can I flash the firmware of the onboard PERC H730 mini (rebranded LSI) in a Dell R530 server? Right now, I have it in pass-through mode, which works fine, but FreeBSD doesn't get any SMART data. With normal expansion card controllers, I would flash…
Crazor
  • 101
  • 1
  • 3
0
votes
1 answer

"LSI Adapter, SAS 3000 Series" - How can I find the specific model?

I'm having trouble finding documentation on this RAID controller. The Windows system details aren't very specific. It just says LSI Adapter, SAS 3000 series, 8-port with 1068E. The server is an HP Z800. Here is a screenshot of the device…
THE JOATMON
  • 275
  • 10
  • 31
0
votes
1 answer

CentOS7 and LSI-9200-8E: How to see all external drives?

I'm working on a low-budget configuration change that involves a migration from a working reflashed IBM M1010 (LSI9220-8i) environment to a newer server running an LSI9200-8e SAS HBA. Everything works fine on the old server, but it uses lots of…
Steve Bonds
  • 1,014
  • 2
  • 12
  • 21
0
votes
1 answer

SSD Raid perfomance

Disks: 10xSSD Ultrastar SS200 960GB 12GB/s Raid 0, 6, 10. Controller: LSI Syncro 9380-8e Filesystem: ext4 without LVM System: Centos 7 2x E5620 @ 2.40GHz 32GB RAM fio-2.1.10: --iodepth=32 --ioengine=libaio --rw=randrw --bs=4k --size 10000M…
shallrise
  • 89
  • 1
  • 13
0
votes
0 answers

ZFS write performance with SAS expander

I have a ZFS storage server running Ubuntu 16.04. I recently added a 12G SAS expander with 6 Seagate ST8000NM0055's. When I create a pool of mirrored vdevs and try to sync data from another array in the server the performance is really bad (rsync…
Eddie Dunn
  • 463
  • 2
  • 9
0
votes
1 answer

Cisco C220 M3 Doesn't Recognize HBA, SSD

I am attempting to set up a Cisco C220 M3 blade server for a company and have been running into issues with the hard driver controller(s) that the machine has. The intent is to have vmWare ESXi installed on the FlexFlash SD cards, 1 SSD on which…
Oren Cope
  • 1
  • 4
0
votes
2 answers

megacli unconfigured(bad) disk status

megacli tell me, there is an issue with one of my disk. Howerver, I am not sure that this disk actually exist. Here is megaclisas-status info : -- Controller information -- -- ID | H/W Model | RAM | Temp | BBU | Firmware c0 |…
Inglebard
  • 153
  • 3
  • 7
0
votes
1 answer

Drive not working with LSI controller

I'm trying to use a NETAPP X412 drive (15K rpm 600GB) with LSI 9240-8i. The problem is that the drive shows up as 0 KB big, and attempting to set the drive to good fails with the error message "Operation not allowed." Other drives on the controller…
Alex
  • 11
0
votes
3 answers

Dell MD1200 (6gb/s jbod enclosure) and 12 Gb/s drives

For reasons too embarrassing and frustrating to blather about, I am the proud owner of a Dell MD1200 enclosure and 12 ST4000NM0014 4TB Seagate drives (short story: I thought they were ST4000NM0023's). The drives show as 475Gb units with both the…
Mike S
  • 1,145
  • 5
  • 22
  • 42
0
votes
0 answers

MegaRAID Controller HDD Not Supported

I'm used to have a LSI MegaRAID Controller with 2 SSDs and 8 Western Digital HDDs. Recently I decided to add another 8 Western Digital HDDs - all 8 TB each - to create a new RAID 5 array. I hot-plugged the drives and checked the S.M.A.R.T status of…
iLLogical
  • 29
  • 3
0
votes
1 answer

How to configure LSI RAID from ubuntu?

I have a Supermicro AOC-USAS2LP-H8iR RAID card, which uses an LSI RAID controller. Unfortunately, I can't seem to get the pre-bios prompt via IPMI (connections drops just before it gets there), so I'm trying to configure it via Ubuntu. I've seen…
Keno Fischer
  • 251
  • 1
  • 3
  • 9
0
votes
0 answers

Unable to enter LSI 'web bios'

Attempting to add a new drive to an IBM EXP3000 SAS Storage Enclosure, connected to an IBM x3850 m2. Upon trying to enter the 'webbios' provided by the lsi raid card, it freezes when start is clicked. This now fails without the new drive, without…
nuggetbram
  • 101
0
votes
1 answer

RAID 6 array rebuild with hotspare

I have an 11-disk (D0 - D10) RAID6 array with a hotspare (D11) - a 12 disk array total. Disk D3 failed earlier today and the hotspare is now being rebuilt (presumably, turning itself into a datacopy of D3). I want to replace the dead D3 with a…
Alex
  • 451
  • 1
  • 5
  • 15
0
votes
0 answers

lsituil basic usage : identify broken disk

We have one disk broken on a server (according to nagios). I would like to get information about the broken disk. I tried to type lsiutil -s. Unfortunately the output doesn't show which physical disk is broken. LSI Logic MPT Configuration Utility,…
bgtvfr
  • 1,262
  • 10
  • 20
1 2 3
…
16 17