Introduction:
Okay so to start I just want to say that the sensor does send its data when commanded as I've tested this on Python connected to a COMPORT on a pc. I will include the Python Code I created that works with the sensor, so that all information is available to you guys. I also will include a link to the PJRC Forum that I've asked the same question on, because I've already gotten responses on the issue, but it still persists, and I want you guys to have what they've said at your disposal.
(Python Code & PJRC Link will be at the very bottom of the post)
Problem:
So, my problem is I cannot figure out how to properly send ASCII commands from the Teensy 3.5 and in return read the output of the Flowmeter with the Teensy 3.5. I am afraid that the hardware is connected wrong or I'm just going about something wrong.
The Serial Console will stay blank meaning nothing is available to be read in
What I've Tried - Software:
This is basic code I was given that should work for my use:
char s;
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
while (!Serial && (millis() < 5000)) {};
Serial1.begin(115200);
delay(1000);
Serial1.print("?\r\n");
}
void loop() {
// put your main code here, to run repeatedly:
while (Serial1.available()){
s = Serial1.read();
Serial.print(s);
}
}
What I've Tried - Hardware:
Image of TSI FlowMeter 5130 w/Cables
Black Wire - USB_C to USB_A - connected to a 5v power supply
Blue/White Wire - USB_A to MALE DB9
Image of Cables that connect the Flowmeter & Teensy 3.5
Blue/White Wire - Male DB9
Tan Serial Gender Converter - Female DB9 to Female DB9
Black Converter Board - Male DB9 to 4-Wire TTL (Red - VCC, Yellow - Transmit, Blue - Receive, Black - GND)
Yellow Wire - Teensy Transmit Pin 1
Blue Wire - Teensy Receive Pin 0
Red Wire - Currently Set to 5v, but I've tried 3.3v to no avail
Black Wire - GND
Image of LEDs Wired into Rx/Tx of Teensy to watch for data being sent
Blue LED - (Yellow - Teensy Receive Pin 0, Orange - GND)
Green LED - (Red - Teensy Transmit Pin 1, Brown - GND)
White Wire - Teensy 5v
Purple Wire - Teensy GND
Python Code:
import serial
import time
index = 0
total = 0
i = 0
avg = 0
# Serial Connection
time.sleep(.5)
ser = serial.Serial(
port="COM2", baudrate = 115200,
parity=serial.PARITY_NONE, stopbits=serial.STOPBITS_ONE,
bytesize=serial.EIGHTBITS, timeout=1)
# Write ASCII Commands To TSI 5300 Flow Sensor
ser.write(b'?\r\n') # Ask Sensor if it is getting a signal (Returns "OK")
ser.write(b'SUS\r\n') # Set Flow type to SLPM (Returns "OK")
ser.write(b'SG0\r\n') # Set Flow Gas to Air (Returns "OK")
ser.write(b'SSR0005\r\n') # Set Sample Rate to 5ms (Returns "OK")
ser.write(b'LPZ\r\n') # Zero Low Pressure Sensor
# Read serial output to remove all 'OK's from buffer
while (i <= 4):
OK = ser.readline() # Read one line of serial and discard it
print(OK)
i += 1
# Ask for 5 Flow readings
ser.write(b'DAFxxxxx0005\r\n') # Read 5 sensor Flow Reading
ser.readline() # Read one line of serial data and discard it
byte = ser.readline() # Read one line of serial data and store it
print("Unfiltered Bytes: " + str(byte))
string = byte.decode('utf-8') # Convert from BYTE to STRING
array = string.split(',') # Convert from STRING to STRING ARRAY
print("String Array of all 5 readings: " + str(array))
# Convert each element of the ARRAY to FLOAT then add them together
for data in array:
index += 1
data = float(data)
total += data
avg = total / index # Find the average Flow in LPM
print("Average Flow Rate: " + str(avg) + " LPM")
time.sleep(1)
ser.close()
