I am using STM32F4 board as slave receiver and nordic board as master transmitter. I am able to send the slave address as 0x30 which is acknowledged by the slave and I send the device register address as 0x10 and I then send some data using
i2c_write(0x30, 0x10, data, 4);
I am able to get the events in my interrupt service routine. I received 0x00020002 for "I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED". I then received 0x00020044 event and the clock stopped running. Can anyone please help me with this. By scoping, I saw Slave address, device register address and my first data with clock on the oscilloscope. But after that clock stopped.
I'm able to use STM32F4 as Master transmitter and read some sensors but I find it difficult to use STM32F4 as Slave receiver with nordic board as Master Transmitter
void i2c_init2()
{
GPIO_InitTypeDef gpio_init;
I2C_InitTypeDef i2c_init;
NVIC_InitTypeDef NVIC_InitStructure, NVIC_InitStructure2;
I2C_DeInit(I2C2 ); //Deinit and reset the I2C to avoid it locking up
I2C_SoftwareResetCmd(I2C2, ENABLE);
I2C_SoftwareResetCmd(I2C2, DISABLE);
/*!< I2C Periph clock enable */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
/* setup SCL and SDA pins
* SCL on PB10 and SDA on PB11
*/
gpio_init.GPIO_Pin = GPIO_Pin_10 | GPIO_Pin_11; // we are going to use PB10 and PB11
gpio_init.GPIO_Mode = GPIO_Mode_AF; // set pins to alternate function
gpio_init.GPIO_Speed = GPIO_Speed_50MHz; // set GPIO speed
gpio_init.GPIO_PuPd = GPIO_PuPd_UP; //Pull up resistor
gpio_init.GPIO_OType = GPIO_OType_OD; //Open Drain
GPIO_Init(GPIOB, &gpio_init);
// Connect I2C2 pins to AF
GPIO_PinAFConfig(GPIOB, GPIO_PinSource10, GPIO_AF_I2C2 ); // SCL
GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_I2C2 ); // SDA
/* Configure the Priority Group to 1 bit */
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitStructure.NVIC_IRQChannel = I2C2_EV_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
NVIC_InitStructure2.NVIC_IRQChannel = I2C2_ER_IRQn;
NVIC_InitStructure2.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure2.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure2.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure2);
I2C_ITConfig(I2C2, I2C_IT_EVT, ENABLE);
I2C_ITConfig(I2C2, I2C_IT_ERR, ENABLE);
I2C_ITConfig(I2C2, I2C_IT_BUF, ENABLE);
i2c_init.I2C_ClockSpeed = 100000;
i2c_init.I2C_Mode = I2C_Mode_I2C;
i2c_init.I2C_DutyCycle = I2C_DutyCycle_2;
i2c_init.I2C_OwnAddress1 = 0x30;
i2c_init.I2C_Ack = I2C_Ack_Enable;
i2c_init.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
I2C_Init(I2C2, &i2c_init);
I2C_StretchClockCmd(I2C2, ENABLE);
I2C_Cmd(I2C2, ENABLE);
}
void I2C2_ER_IRQHandler(void)
{
/* Read SR1 register to get I2C error */
if ((I2C_ReadRegister(I2C2, I2C_Register_SR1 ) & 0xFF00) != 0x00)
{
STM_EVAL_LEDOn(LED6);
/* Clears error flags */
I2C2 ->SR1 &= 0x00FF;
}
}
void I2C2_EV_IRQHandler(void)
{
uint8_t dataRX;
Event = I2C_GetLastEvent(I2C2 );
printf("Event: 0x%x\n", Event);
switch (Event)
{
case I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED :
{
printf("Slave Address Matched\n");
STM_EVAL_LEDOn(LED4);
I2C2 ->SR1;
I2C2 ->SR2;
break;
}
case I2C_EVENT_SLAVE_BYTE_RECEIVED :
{
printf("Slave Byte Received\n");
dataRX = I2C_ReceiveData(I2C2 );
break;
}
case I2C_EVENT_SLAVE_ACK_FAILURE :
{
STM_EVAL_LEDOn(LED3);
I2C2 ->SR1 &= 0x00FF;
break;
}
case I2C_EVENT_SLAVE_STOP_DETECTED :
{
I2C2 ->SR1;
I2C2 ->CR1 |= 0x1;
break;
}
}
}
