We recently have a computer with 3 out of 5 HD going bad (excessive bad sectors) within 1 week. This got me to start thinking that maybe it's the power supply. What are some warning signs / tricks to tell when the power supply is about to go? …
The power supply in one of my servers died.
After a few checks it seems it didn't provided enough power to the machine's hard-disks.
A straightforward solution would be a new PSU but I can't find one like it that has the mains power connector inside…
The motherboard I'm looking to get has a 24pin and 2x 8pin connectors on it. The power supply has a 24pin, 8pin, 4pin, 6pin and a 6+2pin connector. Will this work correctly or should I look for a power supply with 2x 8pin connectors on it?
We have a very relatively simple set up, looking for a very simple (reliable) solution:
Setup:
One Dell box with redundant power supplies running Windows 2003, plugged into two separate APC SmartUPS 1500 units (USB, no smart cards) on two separate…
I have an OEM power supply unit that is cooked. I'm browsing online to find a replacement and am happy to see that they don't cost too much -- the only thing is they all seem to have varying sizes.
Is it a problem if I get a PSU that is smaller than…
Cross-posting this from superuser because they suggested it might get a better response here
Specs
Model: HP Z230
CPU: Intel Xeon e3 1230 v3
RAM: 1x8GB DDR3 Non-ECC RAM
GPU: Radeon HD 8570
NIC: Intel 82571 Dual Port NIC
Storage: 1x128GB SATA SSD,…
Hello fellow Sysadmins.
A C220 M4 with the latest recommended firmware I am working on displays the following fault messages on latest version diagnostics at Server Health:
PSU1 PSU1_PWRGD: Power Supply sensor for PSU1, State Asserted
PSU2…
I have a number of Dell PER740 servers running iDRAC 9 in a lab.
As they are in a lab, I only need/want/have capacity for one power supply connected to each server.
However, I cannot find a way to remove the alert/status that appear in the iDRAC…
I have a Dell T420 and read different ways to upgrade it to redundant PSU's.
Details
I saw on Dell's website a thread where a user asked how to upgrade to a redundant PSU versus the single 550psu. They received a response that explained the parts…
I have a Tower server with today many hard drives and i would like to add hard drives for securing a raid group and also to extend storage capacity.
Hardware spec before adding everything else :
PSU : ENERMAX REVOLUTION D.F. 850W 80+ gold (20Amp…
I bought an HP Server PSU (For mining) - HP PROLIANT 1300w (hstns-pa01) - I plugged it in and it was working perfectly for 12h and 20min, then the rig shut down ( because no power) but PSU fan was still running. I stopped the PSU and unplugged it…
A Dell T420 bought in 2015 was originally configured with the single 550W non-redundant power supply. Replacement parts are cheap these days, and I'd like to replace the single P/S with dual redundant power supplies. Can I simply pull out the…
I purchased a used HP Proliant DL380p Gen 8 off eBay. It has dual redundant power supplies, both at 750 watts. Doing the math, I realize that if both PSUs are at peak load, they will pull 12.5 amps on a standard 120 volt circuit. Given that…
We have a number of SuperMicro RAID 10 boxes with redundant PSU, the same model and spec and use the same rackmount APC UPS. One has suddenly taken to rebooting if there is a minor brown-out.
Windows logs only point to 'unexpected' - as in loss of…
I am setting up a rack in the data center that only has 110V. It is redundant, so I thought I could take one from each leg and get 110V, but when I used a voltmeter last night they somehow are on the same frequency so I don't get 220V out of it. I…