Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [megaraid]

200 questions
3
votes
0 answers

MegaCLI Doesn't allow configured and unconfigured drives with no foreign configs found

I'm fairly new to MegaCLI and I've been having this one issue, after running megacli -CfgLdAdd -r1 [252:0,252:1,252:2,252:3,252:6,252:7] -a0 I get the error Mix of configured and unconfigured drives are not possible. Exit Code: 0x0b which upon a…
Jeremiah Payne
  • 31
  • 3
2
votes
1 answer

MEGARAID RAID 1 SSD WITH HOT SPARE AVAILABLE

I do not know whether this requires immediate action or not. W2012R2 server with two 500GB SSDs plus one identical Hot Global Spare. RAID is Megaraid. Screenshots from the RAID Utility are attached below. This is a business in a small town where we…
RegularExpression
  • 175
  • 1
  • 4
2
votes
0 answers

System slowdown by RAID controller fading away?

May system runs on a RAID 5 on a RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2108 [Liberator] (rev 05) Since about a week the system becomes very slow. I get messages on the commant line like this (taken from syslog) Jan 17 18:16:12…
Timothy Truckle
  • 161
  • 3
2
votes
2 answers

replace RAID controller and keep raid5 configuration

On my system I want to replace my RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2108 [Liberator] (rev 05) with a PERC H310. Will it be possible to import the existing RAID5 configuration with the new controller? My system boots from a…
Timothy Truckle
  • 161
  • 3
2
votes
0 answers

See Pike raid status in ESXi 6.7

I am using ESXi 6.7 and have an Asus Pike 3108 card in the server. When I browse the Host | Monitor | Hardware | Storage I can see: Avago (LSI) MegaRAID SAS Invader Controller #0 But the status is unknown. My understanding is that the VIB…
TSG
  • 1,674
  • 7
  • 32
  • 51
2
votes
1 answer

MegaRAID storage manager update and now tons of media errors

I was just poking around a 5 year old server and noticed the MegaRAID storage manager (14.08.01) appeared to be not responding. The server has been running for something like 400 days without rebooting. I didn't want to reboot it so I installed the…
Kevin Morse
  • 127
  • 9
2
votes
2 answers

Debian - Installation of LSI MegaRAID SNMP AGENT

My OS is : Distributor ID: Debian Description: Debian GNU/Linux 8.9 (jessie) Release: 8.9 Codename: jessie I succeded to install the MegaRaid Storage Manager and I can use StorCli. # dpkg --install lib-utils2_1.00-9_all.deb without…
Sorcha
  • 1,325
  • 8
  • 11
2
votes
3 answers

How to add a hotspare with storcli to a LSI MegaRAID controller?

I have a LSI MegaRAID controller. I pulled out a failed drive and replaced it with a good one. I didn't run any special storcli commands before this, I just swapped the drives. Unsure if that was a mistake. It shows up as UGood: 32:8 26 UGood …
royco
  • 573
  • 3
  • 8
  • 17
2
votes
0 answers

Is RAID 170 a Proprietary RAID Config or a Combination of Traditional RAID Configs?

I acquired a Cisco c240 M4 with twenty-four (24) 800 GB SATA SSD. I requested the engineers configure the disks in two separate RAID 10 arrays (18 + 4), plus with a hot spare for each. The LSI MegaRAID Storage Manager was installed and I used it to…
MZDBA
  • 133
  • 1
  • 6
2
votes
4 answers

Disable hardware RAID controller

I have a storage server with Supermicro X9SCL(+)/X9SCM motherboard and MegaRAID SAS 9240-4i controller. I want to disable RAID to access HDDs directly from OS for further softraid setup. Motherboard manual says there should 4 options: Disabled,…
Islam Sabyrgaliyev
  • 127
  • 1
  • 1
  • 6
2
votes
1 answer

MegaRAID: what does "Is VD emulated: No" mean

When executing "MegaCLI -LdInfo -LdAll -a0", some of my servers report a property "Is VD emulated: No", and some report "Is VD emulated: Yes". I could not find an explanation for this setting, or how to change it. The storcli program allows to "set…
nn4l
  • 1,336
  • 5
  • 23
  • 40
2
votes
1 answer

Recovering Megaraid Storage Array After Power Outage

I suspect I know the answer to this (namely, that there is no hope whatsoever), but thought I'd take the liberty of asking the question in the unlikely event there may be some hope, however remote it may be. I have a server with an old LSI 8888ELP…
user415851
  • 51
  • 1
  • 6
2
votes
1 answer

LSI MegaRAID Bios - Loop where I have to delete Virtual Drive because of Preserved Cache

My server crashed tonight. I suspect the disks being full. I have four SSDs of the same kind connected to a LSI MegaRaid 4-port controller. The disk in slot 1 seems to be troublesome. I guess I could get it replaced. The problem I am running into…
OpenHaus
  • 71
  • 2
  • 6
2
votes
4 answers

Erasing Server RAID Hard disks (SAS and SATA) for decomissioning

We are in a process of decomissioning a handfull of Fujitsu Primergy Servers. Before of course, we want to make sure that the hard disks are completely wiped out. But it seems there is no way to format hard disks one by one as the RAID array…
Diamond
  • 9,001
  • 3
  • 24
  • 38
2
votes
1 answer

Xenserver 6.5 LSI MegaRAID

Is there a package available to install the MegaCLI on XenServer6.5? For 6.5 there is this [1] but 6.5 has another kernel. XenServer 6.5 is based on CentOS6.5 (right?), so I also tried the kmod-megaraid_sas-06.806.08.00_el6.5-1.x86_64.rpm but that's…
Dirk
  • 241
  • 3
  • 9
1 2 3
…
13 14