Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hp]

HP (Hewlett-Packard) is a server and network equipment manufacturer. This is a generic tag to be used when discussing HP hardware or software with no more specific tag available - See the list in the main tag wiki.

HP (Hewlett-Packard) is an American company encompassing multiple brands and product lines, including servers, network equipment, storage equipment, workstations, components, and consumer electronics.

HP has acquired several major industry names in computing, including Compaq and 3Com.

Wherever possible a more specific tag should be used. For example:

,

1513 questions
4
votes
1 answer

Heat generated by a HP ProLiant DL380p Gen8 entry EU servers

I have to buy a stand alone server rack to be placed in a machine room. The temperature can reach 30°C in the room (I have no choice with regards to the location). In order to correct for this I will use active cooling with the used air being…
DavyGravy
  • 159
  • 1
  • 7
4
votes
1 answer

HP StoreEasy 1630 Pool Expansion

We have a single HP StoreEasy 1630 with the following disk configuration: Pools RAID Drives Capacity Virtual_Disks Physical_Disks Size_Per_Disk A 1 2 450GB 1 2 450GB B 5 6 …
Robert
  • 41
  • 2
4
votes
1 answer

How to upgrade the firmware of HP SAS expander card without Smart Array controller or Proliant Server?

How can I update/upgrade/flash the firmware of an HP SAS expander card [468406-B21 a.k.a. 487738-001]? I used to do this using Windows and a HP P410 Smart Array controller, however that controller is no longer available. The online ROM flash…
Pro Backup
  • 984
  • 4
  • 15
  • 35
4
votes
1 answer

HP ProLiant ML350e Gen8 v2 Not Detecting Hard Drives

I have tested several solutions but non of them cant detect my 2 hard drives (legacy mode , acpi and raid embended) I have a 2 Dell-Seagate SAS Cheetah 15k,7 hard drives (ST3300657SS) (they are not brand new and was used on another server) The hard…
warfish
  • 142
  • 1
  • 1
  • 6
4
votes
3 answers

HP Proliant Gen8 boot failure after bios upgrade and processor upgrade

We have a HP Proliant DL360P with one Intel Xeon e5-2650, and we was in need to use two Xeon e5-2670 V2, this server by default this G8 did not recognizes the v2 processor, so we found this procedure so we did the BIOS Firmware update to most…
André M. Faria
  • 154
  • 1
  • 1
  • 7
4
votes
1 answer

HP DL180 G6 amber light but drive is OK

We have an HP DL180 G6 with 25 SFF SATA drives, running 64-bit Debian Linux. A drive recently failed, so we replaced the failed drive with a new, identical part from HP. The disk controller rebuilt the logical volume and the hpacucli command now…
Dave
  • 143
  • 1
  • 4
4
votes
1 answer

Steady red light on 2 HP SAS drives in RAID 1

I have a HP ProLiant web server with two HP 300GB SAS SFF 2.5 inch drives (Model: HP 507127-B21). Both drives have a solid red light, however there is no indication within the management software that either are in a pre-failure state. Also one of…
QFDev
  • 395
  • 2
  • 4
  • 12
4
votes
1 answer

In a HP server, can low voltage DIMMS and standard voltage DIMMs be mixed?

We are adding RAM to a HP Proliant DL380 G7 and were shipped standard voltage DIMMS. We have pre-installed some low voltage DIMMS. Is it acceptable to mix DIMM voltage in general? Is it advised? A technician is attempting to do this now, but the…
makerofthings7
  • 8,911
  • 34
  • 121
  • 197
4
votes
1 answer

Updating firmware on HP ProLiant DL380 Gen8 failed

I tried updating the firmware on my HP ProLiant 380e Gen8, but I received this error: What could be the reason? Could it be because of limited disk space in the /tmp directory? ~ # df -h Filesystem Size Used Available Use% Mounted on VMFS-5 …
Maarten Ureel
  • 239
  • 2
  • 5
  • 12
4
votes
3 answers

HP DL380G6: Where is the Temp. Sensor #29 (System Zone)?

The Temp. Sensor #29 of my HP DL380G6 seems to give me a wrong number. It says that the temperature is more than 50C (Caution: 60C, Critical: 65C) while the actual value is 13C. And I think it may be the reason why all fans run madly at 78% of the…
telicobacter
  • 41
  • 1
  • 2
4
votes
1 answer

Network card location

I am generally familiar with hpacucli and hpasmcli but how do I determine in which slot a network card is installed? I need to be able to map to and from the slot and the MAC (and from there to the interface as Linux sees it), but SHOW SERVER only…
Gaius
  • 1,471
  • 1
  • 12
  • 19
4
votes
1 answer

How do I install HP CentOS repo's

I have been searching for the answer but unable to find any instructions that work for me. I want to install the HP CentOS repo for my new ML310e Gen8 Server to I can setup the insight management software etc for it. Thank you
dgibbs
  • 661
  • 2
  • 11
  • 22
4
votes
2 answers

Configuring VLANs on HP 1910 switch

I understand how VLANs work, but am not quite sure what the various settings in my HP switch actually do. I have an HP 1910 switch, and I'm using the web interface to configure it (personally I'd prefer the CLI, but we have some CLIphobic people…
Grant
  • 17,859
  • 14
  • 72
  • 103
4
votes
1 answer

CPU/RAM upgrade for HP Proliant ML350 G5

I have an HP ML350 G5 server with a single Intel 5130 dual core Xeon installed. Is it possible to upgrade it to a dual processor system? I've looked at the quickspecs and spent a couple of hours searching online but haven't been able to find a…
WaxTrax
  • 217
  • 1
  • 4
  • 9
4
votes
1 answer

DDR3 10600 memory running at 533mhz

I bought a second-hand HP ProLiant DL160 G6 a year ago with 48GB configured in it. I discovered checking with cpu-z and doublechecked with speccy the memory runs at only 533Mhz. I checked the configuration with the HP memory configurator and the…
Elger Mensonides
  • 141
  • 5
1 2 3
…
99 100