Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [controller]

96 questions
0
votes
0 answers

windows server essentials media pack

I have a server 2012 r2 essential build that is already up that is set up on a workgroup. We cannot use a domain controller for this environment. I am wanting to install the media pack, can I do this without a domain controller? I am open to any…
Clucci
  • 11
0
votes
1 answer

Debian / KVM bonding and bridging NICs

I have a physical server with 4 NICs running Debian 8. I want to install KVM and configure guest vm's. One of the guest vm's will run the controller software to manage my network devices (ie managed switches and WAPs). How can I create a bond of two…
user3027361
  • 1
0
votes
1 answer

Can an IBM ServeRAID 4mx controller work on a non-IBM server?

I have some IBM ServeRAID 4mx controllers on some aging IBM x360 servers (Pentium III 1.5 ghz CPUs); I also have a SCSI disk array with two ports, which can be attached to those controllers; and I have two more recent servers which would be a lot…
Massimo
  • 70,200
  • 57
  • 200
  • 323
0
votes
2 answers

Advice on SAS minimum SAS controller specification

I have four HP 600GB 10K 2.5" SAS HDD Drives and I want to buy a SAS controller to connect them to my PC (ASRock Z97Extreme6 Motherboard). My requirements are: They will run under software RAID 1 or 10 under Linux There will be no more that 4 HDD…
Lukasz
  • 63
  • 1
  • 7
0
votes
1 answer

Inter-Controller roaming between Juniper and Cisco AP

Corporate network is mainly composed of Cisco WLC and Lightweight APs. They are all using Wireless G and N. The office is asking to deploy Juniper WLC and APs to a new space in the office. I'm going to implement inter-controller roaming between the…
user192756
0
votes
3 answers

Dell PowerEdge 2900 rom Batt

I have a Dell PowerEdge 2900. I got the the Raid Controller battery warning that it had less than 24 hrs left on it. I replaced it with a new battery. However, after a week, the orange light at the back is still flashing and I still get the same…
Carl-P
  • 1
0
votes
2 answers

What does "Array" refer to in a RAID controller?

This might be a very simple question. Could anyone please explain what the "Array" refers to when it comes to a RAID controller. I have tried searching for it, and I'm just getting more confused.
Arvind Ab
  • 11
  • 2
0
votes
1 answer

9650SE-4LPML RAID Controller BIOs not showing HDDs

I've got a fresh server put together with a 9650SE-4LPML controller card in it with the intention of setting up RAID 1 with two 2TB HDDS. When I boot up and go into the RAID controller BIOs, the drives aren't seen. I've switched out the controller,…
Dave M
  • 1
0
votes
1 answer

Issue rebuilding raid5 with 3ware controller

I have a degraded array with 8 disks. Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-5 REBUILDING 26% - 64K …
Alex Angelov
  • 1
  • 2
0
votes
1 answer

When do domain and forestprep

I have a simple domain with a single Win2003 server. I just upgraded the funcitonal level to Win2003. I am now trying to add a Win2012 DC, but it warns me that the functional level is still at w2000 I upgraded it 5 minutes ago, with a single DC, do…
TSG
  • 1,674
  • 7
  • 32
  • 51
0
votes
2 answers

Centos 5 SAS controller

NOC tech told me this: I am having troubles loading this server. I set up the HDD in the RAID controller however it does not show up when I try to install CentOS. A quick look at SuperMicro's website shows that this board (X7DCL-3) does not support…
Clear.Cache
  • 89
  • 1
  • 1
  • 11
0
votes
1 answer

Smart Array P212 Raid controller on SBS 2008 ProLiant G6

I had a mirrored array with 2 * 1TB drives. I have replaced both drives (one at a time and allowed it to rebuid) with 2 * 2TB drive. So I now have a capacity of 2TB rather than 1TB. However, the array is now reporting to have 1.8TB of unused space.…
Kip
  • 1
  • 1
0
votes
4 answers

Adaptec 2820SA RAID 5 Question

We have a Server in our office with an Adaptec 2820SA RAID contoller in it, and since the day we got it its been purely excellent. However, we recently wanted to increase the size of our storage options and have bought 4 x brand new 1.5TB drives for…
Ash
  • 143
  • 1
  • 1
  • 8
0
votes
1 answer

Read only active directory option is greyd out

I want to deploy a RODC sever in an existing domain.I fulfilled all pre-requisite for RODC.There are two DCs in the domain both 2008 r2.When i try to install third DC in same forest,the Read only active directory option is greyd out. It say there…
rahul
  • 3
  • 1
0
votes
2 answers

Drive stopped working on windows server 2003 and I receive a "controller error"

I have a Proliant 360 Hp server with Windows server 2003 R2. I can only access the server in safe mode. The event viewer is completely filled up with this error: The driver detected a controller error on Device\Harddisk3\DR3 I figured out which…
Durden81
  • 131
  • 5
1 2 3 4
5
6 7