Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [cisco-vpn]

240 questions
1
vote
1 answer

vpn connection is OK but can't route some IPs

Our Network is laid out as in the diagram below PC1 can successfully connect to server 2 (with 10.120.20.x/24), and PC4 can successfully connect to server 1 (with 10.120.30.x/24). Our problem is that the PC on the right hand side (with IP =…
cxit
  • 11
  • 1
1
vote
1 answer

Uniting 3 Locations Through VPN

Hello and thanks in advance, My issue is that, at the moment, my company has two locations. We'll call them "A" and "B". I already have them synced using a VPN. We just purchased another building this past month and I need to also sync that…
Franco G Marannano
  • 13
  • 2
1
vote
0 answers

vpnc through openvpn failed

I should connect to a Cisco VPN server for example 95.94.66.6, it configured to accepts specified IPs so I launched a server with a registered IP on Cisco which runs an openvpn server. The scenario is like this: I connect to my vpn server then…
Farhadix
  • 111
  • 3
1
vote
3 answers

Problem with installing Cisco VPN Client on Windows 7

When attempting to install Cisco VPN version 4.9.01, I am getting the following error: The driver is blocked due to compatibility issues Driver: Deterministic Networks Publisher: Deterministic Networks Location: Not Available This driver is…
Mike Messina
  • 89
  • 4
  • 12
1
vote
1 answer

Cisco 2901 - IPSec VPN Maxing CPU

We have a Cisco 2901 on the edge of a 100Mbps/100Mbps WAN link which is providing an endpoint for an IPSec VPN to a Juniper SSG 550M. The problem is that we are seeing a max of 'only' 40Mbps over the IPSec VPN, and when the VPN is at capacity the…
Antix
  • 383
  • 1
  • 6
  • 19
1
vote
1 answer

IpSec/Racoon: Packets go to wrong tunnel

I use Debian and Racoon to connect to a Cisco VPN Gateway. We have got two tunnels between the same endpoints. Somehow and sometimes, packets go to the wrong tunnel. This is the log message from the remote Cisco system: Aug 13 17:55:01 XXXXX…
Matthias Wuttke
  • 123
  • 1
  • 9
1
vote
1 answer

Cisco ASA - NATing internal -> internal IP for users on a VPN

RemoteSite (172.16.1.*) | Internet --- InternetUsers | ASA --- LocalUsers (192.168.1.*) | InsideNet (10.1.1.*) | Router | DeeperNet (10.22.22.*) I have a Cisco ASA 5510 with three interfaces,…
DrStalker
  • 6,946
  • 24
  • 79
  • 107
1
vote
0 answers

Cisco RV042 can ping gateway only

I have Cisco RV042 which the problem is can ping gateway only. here my setup : LAN Setting Device, IP address : 172.31.13.254 Netmask : 255.255.255.248 Dual Wan Setting WAN 1 Static IP: IP Address : 202.xx.xx.254 Netmask : 255.255.255.252 Def GW :…
Pathic
  • 121
  • 1
  • 5
1
vote
1 answer

VPN Tunnel set up Issues - Cisco WRVS 4400N to Server 2008 R2behind ASA5505

I was wondering if someone could help with a scenario i have that i am not sure how to set up regarding a VPN tunnel set up. I have a Cisco WRVS4400N business router , and on this device , i need to be able to set up a constantly running VPN…
Matthew Lowe
  • 11
  • 2
1
vote
1 answer

How to configure remote IP address audit logging for VPN clients on a Cisco 2801

We have a Cisco 2801 that also acts as a VPN Server for Cisco VPN Client. We would like to configure IP address logging so that each time a user connects using VPN we would like to log his IP Address. So far there were only 3 of us. However as time…
Spirit
  • 1,154
  • 8
  • 25
  • 45
1
vote
2 answers

Resetting Cisco VPN on a Mac?

Sometimes our Macs will get Error 51: Unable to communicate with the VPN subsystem. Please make sure that you have at least one network interface that is currently active and has an IP address and start this application again. when starting Cisco…
Mark Harrison
  • 805
  • 2
  • 12
  • 20
1
vote
0 answers

Setting up an IPSec VPN with Cisco ASDM

I am trying to set up a VPN remote access with a Cisco ASDM 6.4 for ASA 5505 Version 8.2(5). In order to set up the VPN I followed this steps. After this steps my info look like this: VPN Tunnel Interface: outside PPP authentication: MS-CHAP-V1…
Ignacio Gómez
  • 111
  • 2
1
vote
1 answer

Cisco VPN and .pcf file

I have few of profiles .pcf files , and I used them in order to automate the vpmclient connection VIA CLI command I have WIN XP server for example vpmclient connect "customor_alpha" until now everything is ok but I have problem with the…
yael
  • 2,433
  • 5
  • 31
  • 43
1
vote
3 answers

Cannot Make a Cisco IPSec VPN Connection Through a PFSense Firewall

We are building an onsite network here and we are using PFSense 2.0 as our firewall. We have no trouble connecting to various services and other VPNs but for some reason we cannot connect using cisco's IPSec VPN client -- either the cisco branded…
Wyatt Barnett
  • 725
  • 5
  • 14
1
vote
1 answer

ICS with Cisco AnyConnect - cisco-anyconnect-win-3.0.4235-pre-deploy-k9.msi

I've installed cisco anyconnect VPN (cisco-anyconnect-win-3.0.4235-pre-deploy-k9.msi) on a 64 bit Windows 8 machine. FYI, I do have internet access, while I'm connected to the VPN. I want to share this VPN connection, so I can use some other…
FatherFigure
  • 285
  • 1
  • 2
  • 14
1 2 3
…
15 16