Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [cisco-pix]

The Cisco PIX line of products were devices that provided firewall and VPN functionality.

The Cisco PIX line of products were devices that provided firewall and VPN functionality.

They have been replaced by the Cisco ASA line of products. Many of the configuration commands used in PIX are the same or similar to those used in ASA, particularly earlier versions of the ASA operating system (version 7.x). Therefore, many useful answers to PIX related questions may be found under Cisco-ASA questions.

85 questions
0
votes
2 answers

Loss of inbound emails from external domains after replacing firewall with new ASA5510

To start, I'd just like to admit my lack of knowledge in setting up/maintaining critical hardware like firewalls and exchange servers. I am the Technology Coordinator for a small charter school and came into this position about 6 months ago, where,…
Brady
  • 1
0
votes
1 answer

HTTP traffic through PIX VPN from outside site

I have a remote site with a website that only allows access from the outside IP assigned to our local PIX. I have users connecting to the local networking using a VPN that need to be able to view this remote site. I don't think this works because…
fwrawx
  • 187
  • 3
  • 11
0
votes
3 answers

Set up a GRE tunnel with Cisco PIX-506 v6.3

I'm trying to establish one half of a GRE tunnel, the other being configured by my service provider. I have a Cisco PIX-506-E running Firewall version 6.3(5). Provider Router Public IP: 8.8.8.8 My PIX Public IP: 7.7.7.7 Provider Tunnel Address:…
Antonius Bloch
  • 4,680
  • 6
  • 29
  • 41
0
votes
3 answers

What are tha main causes of slowness on Cisco PIX 515?

A couple of Cisco PIX 515 work in standby mode. But the active PIX (or the otherone) never uses more then 40% of the available bandwidth on the outbound LAN interface (10Mbps).
luciano
  • 1
  • 1
0
votes
1 answer

Disable VPN on Cisco PIX 506e (v6.3) and configure VPN pass through to a Windows 2003 DC/RRAS

The company I work for has a client that has a Cisco PIX 506e firewall running v6.3. The PIX is currently set up to manage PPTP VPN connections using the local Windows domain controller as a RADIUS server. The PIX does not support MSCHAP v2…
Strahn
  • 35
  • 4
0
votes
1 answer

Cisco pix 501 setup with Mcafee

I am way out of my leauge on this but if someone could take the time to help me I would appreciate it. We renewed our Mcafee Saas Protection and I am trying to set up their required ip addresses in our cisco pix 501 so there servers can route emails…
aaron
  • 21
  • 2
0
votes
1 answer

PIX 506E with multiple external /24 subnets

I've got two internet accessible /24 subnets, lets say 11.22.33.0/24 and 44.55.66.0/24 which I want to pass to servers using a private 10.0.0.0/24 subnet behind a PIX 506E e.g. requests to 11.22.33.99 and 44.55.66.99 either both get sent to…
thelem
  • 105
  • 5
0
votes
1 answer

Can a CISCO PIX tunnel SCTP traffic over an IPSEC tunnel

Can a cisco PIX 515e tunnel SCTP traffic over an IPSEC tunnel ? I Know that the PIX doesn't support SCTP connection's but SCTP is still IP so i'm hoping the PIX has the capability to route SCTP over an IPSEC tunnel. Also how would the access-list…
Steven Williamson
  • 170
  • 1
  • 6
0
votes
1 answer

IE halts loading HTML page abruptly, possible network issue

Understanding that my problem could have a very vast scope of possibilities, I'll accept the answer that points me to something that I might have missed. My software's client is facing this issue of page stopping loading in the middle and that too…
Vishal Seth
  • 101
  • 1
0
votes
2 answers

Asterisk Sip trunk though a PIX 501 firewall

I'm using an asterisk VOIP server, and I'm able to make called though with my SIP client. The problem I get is one-way voice. I can hear the incoming voice but the caller can not hear me. I have no problems when using the X-Lite3 windows SIP client.…
Squidly
  • 1,765
  • 1
  • 14
  • 18
0
votes
2 answers

Converting cisco PIX to cisco ASA

I am about to migrate PIX 515E, 6.3(4), configuration to Cisco ASA. I do not have the PIX which is in Paris, I have the configuration on a notepad file. I do not know the Cisco ASA model yet either which is going to be delivered on next week. I…
daffodil
  • 1
  • 1
0
votes
1 answer

Cisco Pix - how many clients or peer sites supported?

I read that a cisco pix 506e supports up to 25 vpn peers (sites), and unlimited clients (machines connected with the cisco vpn software?). The lowest cost option would seem to be to install the vpn software on all the remote clients…
Scott Szretter
  • 1,882
  • 11
  • 43
  • 66
0
votes
4 answers

Assistance with PIX 501 Firewall

This should be a simple edit, but for some reason I am stumped. We switched the ISP at a worksite. For these purposes I'll post the new static IP info as: IP - 10.1.1.50 Sub - 255.255.255.0 GW - 10.1.1.1 And the old info as: IP - 10.2.2.100 Sub -…
Dennis
  • 1
  • 1
0
votes
2 answers

What does fixup protocol http actually do on a Cisco PIX firewall?

I have a PIX 515E, running PIXOS 6.3, which has fixup protocol http 80 in the configuration. Can anyone point me to documentation that describes exactly what this does to web traffic. Cisco's own command reference says: fixup protocol http The…
Richard Gadsden
  • 3,686
  • 4
  • 29
  • 58
0
votes
1 answer

Cisco PIX 515 doesn't seem to be passing traffic through according to static route

Ok, so I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to…
Liquidkristal
  • 41
  • 1
  • 6
1 2 3 4
5
6