16

I do not have a meat tenderizor. I want to fry my chicken breasts but need to pound out the meat. What can I use instead?

Tuorg
  • 1,091
  • 6
  • 11
Sandy Brown
  • 179
  • 1
  • 3
  • 1
    some more tips on pounding the meat: https://cooking.stackexchange.com/q/81/69382 – Ess Kay Dec 17 '18 at 17:32
  • 2
    I've heard of covering it with plastic wrap and using an unopened food can, e.g. a can of soup or beans... – adfaklsdjf Dec 18 '18 at 17:56
  • 2
    Possible duplicate of [How do I pound chicken (or other meat) without making a mess?](https://cooking.stackexchange.com/questions/81/how-do-i-pound-chicken-or-other-meat-without-making-a-mess) – Rob Dec 18 '18 at 18:45
  • 2
    Just about anything can be used as a hammer. – Mast Dec 19 '18 at 17:50
  • 2
    Am... am I allowed to make lewd jokes in the comments? ;D – AmagicalFishy Dec 20 '18 at 22:56

10 Answers10

40

This might seem silly but, . . . I use my fist. I always cover my chicken with plastic wrap to contain the mess before I pound it. You can also glove up instead/as well.

I have found that punching it is just the right amount of force for the job. And the uneven surface of my knuckles acts as a meat tenderizer and breaks up the tissue just a little. (But not too much.)

Summer
  • 3,022
  • 1
  • 12
  • 25
35

Anything flat, non-breakable, and reasonably heavy would work: rubber mallet, rolling pin, flat-bottomed wooden bowl, etc. I would suggest protecting the meat and implement from one another with plastic wrap.

Tuorg
  • 1,091
  • 6
  • 11
  • 24
    ... small skillet or frying pan... the list goes on and on. – Stephie Dec 17 '18 at 16:05
  • 4
    A can of food (e.g. soup or beans), that you plan to open soon anyway since it may become dented during the process. – user3067860 Dec 17 '18 at 18:45
  • 5
    I find that placing the chicken under saran wrap (clingfilm) and whacking it with a rolling pin does the trick just fine – Richard Dec 17 '18 at 18:50
  • 1
    I've used bottles for similar purposes, in the past. Grab at the neck and strike with the bottom. I also always use some sort of plastic wrap or a nylon bag to protect the meat. For bonus points, put some seasoning inside it (e.g., salt and pepper). – VLAZ Dec 18 '18 at 07:00
15

Put breast between baking paper, roll like dough with a rolling pin. If you have any spices/herbs/salt/pepper to add you can sprinkle then mid rolling as this will push them inside meat.

SZCZERZO KŁY
  • 4,131
  • 13
  • 15
8

Put it between two plastic sheets, or inside of a zipblock bag big enough to accommodate the smashed size of the breast.

Then you're going to want to grab a skillet and beat that meat into submission. Cast iron is the classic here, but anything you can swing will work. Just make sure the skillet isn't hot or warm when you start assaulting that meat.

4

I've been known to cover with plastic wrap, lay my chef's knife flat along a piece of chicken, and then hit the flat of the blade with the heel of my hand. Obviously, stay away from the sharp / pointy parts; but that is easy to do with a big chef's knife. I typically only do this when I have one or two pieces of meat that need tenderizing (as anymore will tenderize you back!)

Van
  • 477
  • 3
  • 13
4

We designed ourselves a wooden block (remains from a 2" laminate floor joist) about 8" by 8", drilled a hole in one side, and screwed in a handle. When we use it, we wrap it around and around with plastic wrap to keep the meat clean.

We would then use this as an intermediate, placing the chicken breasts underneath it, and pound it with a 3 lb sledge hammer. Though it sounds a bit extreme, it is actually quite effective, works quickly, and does not damage the meat.

anonymous2
  • 181
  • 4
3

I've seen my mother use a Corningware plate or saucer in place of a meat tenderizer. She would just hold the plate sideways and pound out the meat with the edge of the plate.

R. McMillan
  • 131
  • 2
2
  1. Iron Skillet (or another heavy pot/pan)
  2. Cutting board
  3. Rolling pin - really easy if you have the French tapered kind
  4. Big can of tomatoes...
  5. An empty wine bottle
  6. A pool ball (the kind you use on a table...not in the water!)

Bon Appetit!

Erica
  • 8,362
  • 9
  • 60
  • 89
Hope 2 Help
  • 21
  • 1
1

First off, you'll definitely want your chicken between two sheets of plastic. You can either do this with two sheets of plastic wrap, or by putting it in a gallon ziplock bag (don't seal it though). The best alternative tool to use is a rolling pin as it's got no sharp edges (will break your plastic and can cut the chicken in half) and has weight and length to aid in leverage when whacking. Not everyone has a rolling pin, so if you don't just grab the largest heaviest can of food you have and slam it into the chicken. I wouldn't use any beverage cans, and especially not anything carbonated like soda or beer. I actually have a purpose built meat tenderizer and prefer using my rolling pin.

Sdarb
  • 1,109
  • 1
  • 8
  • 19
1

I have used a cast iron skillet against a cutting board. Plastic wrap or parchment paper to protect the surfaces...

KMcCMedia
  • 11
  • 1