Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [ubiquiti-edgerouter]

EdgeRouter is a line of network routers from Ubiquiti Networks.

40 questions
1
vote
0 answers

Assigning a single public IP address to a VLAN with NAT

I've been assigned to be in charge of our business' networking and am a bit out of depth here. We have a few production services running on multiple servers, currently sitting behind a NAT and a single public IP address. We separate the traffic by…
Alex
  • 11
  • 1
1
vote
1 answer

XenServer (Citrix) Management Network Interruption

We have an OOB/management network we use to loginto storage, hosts etc. We're using VLANs to separate out storage, from hosts, to camera's etc. We would like to replace this switch with a new one using the previous config but we're wondering what…
Sherlock
  • 23
  • 2
0
votes
1 answer

Azure P2S VPN routing issue

I set up a Virtual Network on Azure a few days ago and connected our local business Network through a site-to-site VPN Connection with the virtual network. Everything is working fine so far. Then I also set up a Point-to-site VPN connection with my…
M4SX5
  • 13
  • 1
  • 7
0
votes
1 answer

Ubiquiti EdgeRouter uses default route over static when responding to ICMP

I need to have a working connection between two router devices and the subnets behind them. Everything else in the setup seems to work except one static route. Here is the basic information about my setup: Juniper: Vlan95 10.250.0.1/24 Vlan1 …
nyoatype
  • 65
  • 1
  • 9
0
votes
0 answers

New Ubiquiti router potential DNS issues?

We have a SonicWall as our business router for around 50 ish people. Recently it was getting super slow, and it turns out the fans in it died and it was overheating. I've replaced it with a Ubiquiti EdgeRouter 4, and everything sped right up, and so…
Brian Leishman
  • 111
  • 1
  • 8
0
votes
1 answer

DNS/DHCP configuration in /config/config.boot vs. /etc/dnsmasq.d

I have an Edgerouter 4 and I am trying to make sense of the configuration areas for DHCP and DNS, when use-dnsmasq enable is set. I see four places where the configuration can be done: from the command line (set service dns forwarding ... seems to…
WoJ
  • 3,607
  • 9
  • 49
  • 79
0
votes
0 answers

OpenVPN DNS resolution issue on router (EdgeOS)

I've been using OpenVPN client over vtun interface and all works as expected only if the remote VPN server name (in the OpenVPN config) is the IP address. When I use the DNS name as part of the OpenVPN config "remote" OpenVPN cannot establish…
Tamir
  • 101
  • 2
0
votes
1 answer

EdgeRouter X as VLAN-only Switch

The Ubiquiti EdgeRouter X (ERX) has a switching chip on board so that it can be used as an L3 switch instead of as a router. I have another router, we'll call it router-core, which is serving an internal network on VLAN 100 on my local network. What…
enpaul
  • 202
  • 2
  • 13
0
votes
1 answer

EdgeOS BGP routes received but not being injected

I'm trying to set up BGP over IPSEC with Google Cloud Platform. The IPSEC tunnel is successfully established, and GCP reports the BGP session as up. EdgeMax router is receiving the routes, but isn't injecting them into the RIB. dan@router:~$ show ip…
Isvara
  • 215
  • 2
  • 13
0
votes
1 answer

How can I restrict access (by IP) to devices behind my Edge Router?

I have a Ubiquiti ERPro-8 with some servers behind it. I would like to allow access to those servers, on specific ports. But I would like to restrict access to those servers by IP address. For example: Allow access to 10.0.1.40:8080 from…
Sathed
  • 101
  • 4
0
votes
0 answers

The Chrome browser can sometimes not reach Google servers with a new router

I have an odd problem which I haven't been able to even find mentioned elsewhere. A while back, I switched out the Wifi access points as well as the router for a small office network. After I did this, most everything started working better, with…
kqr
  • 91
  • 1
  • 9
0
votes
1 answer

How to configure failover in edgerouter x 5 ports?

I have connected to my edgerouter x 5 ports, 2 WAN (WAN1 to eth0 and WAN2 to eth1 in failover) Problem: WAN1 has 10 Mbps and WAN2 Failover 8 Mbps. When WAN1 drops, but not enough (example: 1 or 0.5 Mpbs), WAN2 failover does not enter. What I want is…
acgbox
  • 376
  • 1
  • 5
  • 21
0
votes
0 answers

How to receive mirrored traffic on remote host using Ubiquiti EdgeRouterX?

I have the current network setup: two subnets are connected using an Ubiquiti EdgeRouterX, subnet 1 has a switch mirroring all traffic on that subnet to the router and on subnet 2 there is a host where I want to receive all the mirrored data. Using…
Juan Martinez Alonso
  • 1
  • 1
0
votes
0 answers

IPSec VPN between StrongSwan and DrayTek Router fails on second rekeying

I want to establish an always-on IPSec VPN between a DrayTek Vigor2860 and an EdgeRouter X (which uses StrongSwan). The Draytek is behind a NAT and dials into the ER-X. The VPN connects and works, but disconnects at the second rekeying. It then…
masgo
  • 433
  • 1
  • 4
  • 12
0
votes
1 answer

EdgeOS Ansible Issues

I'm getting the following when trying to run a playbook using the edgeos_commandmodule: An exception occurred during task execution. To see the full traceback, use -vvv. The error was: ansible.module_utils.connection.ConnectionError: ssh connection…
Brian Lamb
  • 59
  • 1
  • 4
1
2
3