Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hpe]

103 questions
0
votes
2 answers

Monitoring processes/services Error by Zabbix over HPe Server

Would you mind sharing your experience with me? I monitor the ilo HP server with Zabbix Whenever there is a problem with the RAM or hard disk on the server, I receive a critical alarm through this OID. 1.3.6.1.4.1.232.6.1.3.0 It's just that, even if…
sasanalem
  • 1
  • 1
0
votes
1 answer

Issues with Ubuntu not booting on HPE Proliant ML30 Gen9

One of the server machines we use for database backup procedures is having issues and I ran out of ideas. At some point, it froze completely, and so it was forcefully rebooted. After that, the machine couldn't boot into the OS anymore. The machine…
Maximiliano Segovia
  • 1
  • 3
0
votes
1 answer

Fedora Server 34 crashes randomly every few minutes on HP ProLiant DL380e G8

I am unfortunately having a problem with my HP ProLiant DL380e G8 server running Fedora Server 34. I suspect these are memory errors or a DIMM being/going bad, however I'm not sure. Feedback is very welcome! I've ran journalctl -r, which returns the…
jonasclaes
  • 101
  • 7
0
votes
2 answers

P420i controller / 2 disks failed in RAID5 / RAW FS after parity initilization

We woke up this morning with 2 failed disks on RAID5 with a single hot-spare configuration. Hot-spare disk didn't replace any damaged disk maybe because there are 2 disks failed at the same time. However, I added two new disks and the parity is…
Maroon
  • 1
0
votes
1 answer

Is it possible to coonect the power to the sata power slot on a PCIE card from HPE ProLiant DL360p Gen8 server?

This is my first server and I never had one before... I recently need to use USB 3.0 for external HDD but there is none on this server, all USB 2.0. So I bought a "3 Ports USB 3.0 with 1Gbps Gigabit Ethernet Controller PCIe Expansion…
Arst
  • 101
  • 1
0
votes
0 answers

Connect extra 4 SAS HDDs to HPE Proliant Dle360 gen9

I have an HPE Proliant Dle360 gen9 configured with 1x 500w PS, 32GB ram, 1x 12 core Xeon cpu. At the moment its 4 front bays are occupied by 4 SAS HDDs. I want to replace them with 4 SAS SSDs and also reconnect the 4 SAS HDDs some other way. Do I…
Michael
  • 1
0
votes
0 answers

HP MicroServer N54L - HP logo light not lit

I bought an HP MicroServer N54L recently, and a few days ago, upgraded the RAM to 8GB from 4GB. When I booted it up again, the HP health LED lit up red briefly, then turned off again. I noted that the power LED was on, fans were spinning, but the HP…
archie
  • 1
  • 2
0
votes
1 answer

HPE SSA: After completing the configuration - reboot the system

From the HPE ProLiant System Utilities (BIOS) I booted into HPE Smart Storage Administrator (SSA) to migrate a logical drive with RAID6 (and existing data) to RAID5. After starting the migration task, which would need several hours to complete, the…
stackprotector
  • 596
  • 1
  • 8
  • 27
0
votes
1 answer

HPE Proliant Gen10 Stack Fault Exception during PXE boot with UEFI

I am trying to pxe boot a HPE Proliant Gen10 using UEFI BIOS with RHEL (have tried both 7 and 8) and am getting a stack fault exception after the server receives the first boot file (shimx64.efi): HPE ProLiant System BIOS U32 v2.42 (01/23/2021) (C)…
Mike
  • 1
  • 1
0
votes
1 answer

G9 DL380 with no smart array controller

I'm planning on running Ceph cluster on HPE G9 DL380 servers. As I have used the servers for Ceph cluster, there is no RAID requirement for the servers. My question is, do I need to purchase smart array controller (like Smart Array P440ar…
user393397
  • 37
  • 4
0
votes
0 answers

HPE ProLiant DL380e Gen8 - ILO seems OK but server does not power up

I have an HPE ProLiant DL380e Gen8 rack server. I can't make the server power up. It stays "silent". The ILO 4 web interface works fine and it shows status: System Health: [tick] OK iLO Health: [tick] OK Server Power: OFF I don't see any problems…
MrSnrub
  • 153
  • 1
  • 3
  • 9
0
votes
0 answers

How to get temperature readings of HP P420 RAID PCI-e card?

I have an HP Proliant ML110 G9 Server. Added an HP Smart Array P420 PCI-E card to have real hardware RAID on the server. Everything works fine, but I noted that the P420's processor was extremely hot (I realized by touching the sink). Added an extra…
J.L
  • 41
  • 5
0
votes
2 answers

HP Proliant ML350 Gen9 doesn't start

We have a HP Proliant ML350 G9 server and yesterday it just stopped suddenly. Checked the power supply and it's stable 220 VAC. Server has two power supplies and both of them are lighting green. Also UID is blinking blue. On the front panel all 4…
Pomzr
  • 1
  • 1
0
votes
0 answers

Booting from CD-ROM image with HP server in UEFI mode

I have a ProLiant BL460c Gen9 server, on which I want to install my OS with UEFI mode. After I changed the boot mode to UEFI and disabled secure-boot and tried to boot my Centos7 Image from CD-ROM this is what I…
Dvir Saidof
  • 1
0
votes
0 answers

Upgrading Intel DC S3500 HP OEM firmware without Windows Server?

I have a second hand 800GB SSD Intel DC S3500 series (Model VK0800GDJYA). The Intel DC S3500 series suffers from the 8MB bug if the firmware is not updated: the capacity of the SSD suddenly fells to 8MB, for instance after a power outage. Some of…
OuzoPower
  • 347
  • 1
  • 4
  • 11
1 2 3 4 5
6
7