Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [dhcp-server]

Dynamic Host Configuration Protocol (DHCP)

The DHCP service is a client/server application that allows "clients" to obtain configuration information (typically for network settings) from a "server".

Questions carrying this tag should focus on the server-side more than the client-side.

540 questions
0
votes
1 answer

DHCP Authorization for Non-Windows Devices

I hope I can nail this question because I keep having a difficult time framing it properly. I'm looking at the feasibility of configuring switches to act as a DHCP server. In this article…
marcus
  • 3
  • 4
0
votes
2 answers

Why are DHCP request and acknowledgment messages broadcasted and not unicasted?

In 'Request' part of the DORA process, IP and MAC address of the DHCP server is known to the client (as the IP datagram sent in Offer has this information). So if the destination is known, why is the request still broadcasted to every machine on the…
Paras Gera
  • 3
  • 3
0
votes
1 answer

What happens when "Auto state switchover interval" is less than "Maximum client lead time" in DHCP?

I was wondering what happens when "Auto state switchover interval" is less than "Maximum client lead time" in DHCP? The question was raised after reading definitions of MCLT & ASSI: Maximum Client Lead Time: This determines two three things: A)…
Sam
  • 209
  • 1
  • 4
  • 9
0
votes
1 answer

is it possible to use cobbler using windows dhcp server or without dhcp?

I want to configure cobbler in my network but my network already managing by a windows 2k8r2 dhcp server. Is it any way to configure without dhcp server ?
user1812956
  • 85
  • 1
  • 3
  • 10
0
votes
0 answers

How to disable or turn off DHCPv6 on Cisco 3939B router?

I am trying to set up a Windows Server 2012 R2 Essentials server properly. I would assume it could also apply to non-Essentials also. i.e. Standard. DHCP for BOTH IPv4 and IPv6 MUST be turned off or disabled on the router before setup of the…
timd1971
  • 287
  • 1
  • 5
  • 15
0
votes
1 answer

Error when configuring a failover DHCP: "The following scopes already exist on the partner server"

Server 2012 R2 I get that error message when clicking next in the Failover Wizard after specifying the partner server, but I don't understand it. In trying to research how to setup a failover DHCP the one thing I didn't understand or find was the…
Alan
  • 1,003
  • 2
  • 20
  • 36
0
votes
1 answer

Polycom phone not requesting DHCP offer

My Polycom IP550 phone is not requesting the DHCP address that my windows 2012 server offered it. I have done a wireshark capture on a mirrored port on our switch and you can see that the phone is doing the discover phase of the DHCP cycle and the…
Systems Party
  • 77
  • 1
  • 7
0
votes
1 answer

DHCP attribution without DHCP client

j'ai un serveur DHCP qui attribue des IP selon les adresses MAC des clients. J'ai un client qui n'a pas de client DHCP installé (pas que je sache). I have a DHCP server (on linux) which gives IP address depending of the MAD addresses of the clients…
Shan-x
  • 168
  • 2
  • 9
0
votes
2 answers

How to block DHCP traffic using iptables

First let me describe my environment: There is a VM (CentOS) acting as a gateway The gateway VM has to NICs, eth0 connects to public network, eth1 connects to private network eth0 get IP from public network's DHCP server The gateway contains a DHCP…
TieDad
  • 274
  • 5
  • 13
0
votes
1 answer

DHCP Config for Server 2012 R2

This question may have been covered before, but it is rather complex and haven't found a similar post, so please be kind! I think my issue is rather unique, so I'll try to explain as best I can. I'm currently configuring a domain at home for my new…
user269224
0
votes
1 answer

calculate reserved ip address based on mac address

Is it possible to calculate ip address based on mac address for isc-dhcp server? For example: 'aa:aa:aa:aa:aa:x' => '10.10.10.x' I have following in dhcpd.conf: subnet 10.10.10.0 netmask 255.255.255.0 { class "v" { match if substring…
kakabomba
  • 113
  • 4
0
votes
1 answer

How to configure DHCPD server to bind static IPv6 address by DUID?

how can i configure the server to make static record DUID - IPv6 ? For example i have such DHCPv6 request: Client Identifier Option: Client Identifier (1) Length: 7 Value: 31303030303133 DUID: 31303030303133 # <--- this …
Vololodymyr
  • 113
  • 1
  • 5
0
votes
0 answers

CentOS DHCP server supporting multiple subnets on a single NIC

I understand that what I am asking has been asked a million times already. I think I have read just about every post I can find on the subject yet I still cannot get this to work. I have a DHCP server (centos 6.x) sitting in vlan1. I am running a…
inunendo
  • 1
  • 1
  • 2
0
votes
1 answer

XenServer 6.2 DHCP Setup

I have a XenServer 6.2 running on a dedicated OVH Server. For this dedicated server I have 2 additional IP blocks. Whenever I setup a new VM (mostly CentOS 6.6) i have to skip the network configuration part and do it manually after. Is there any way…
Andreas Hinderberger
  • 142
  • 2
  • 2
  • 10
0
votes
1 answer

Change DHCP on server 2k3

Ok I am trying to mess with our dhcp settings on our domain server because at this point we kinda have competing dhcp servers between the router and the server. (Long predates me and I have finally got tired of it.) The server will give out ip…
birdman3131
  • 101
  • 1
1 2 3
…
35 36