Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [access-point]

184 questions
0
votes
1 answer

Add Access Point to Sonicwall TZ100

I have a SonicWall TZ-100 configured with two private networks, 192.168.1.x LAN and 192.168.10.x WLAN. The WLAN is bridged to the WAN so traffic goes direct out through the WLAN and never access our internal LAN. SonicWall DHCP is enabled for the…
Jeremy Smith
  • 123
  • 7
0
votes
3 answers

How to prevent users from connecting directly to the switch, where the Access point is connected?

I'm about to setup a large wireless network, at a dorm. The hardware I'm using is going to be: HP Procurve E2520-24G-PoE (J9299A) Cisco Aironet 2602i Autonomous Access Point Since the outlets at the AP's are being mounted on the wall, so everyone…
Daniel
  • 218
  • 1
  • 3
  • 11
0
votes
1 answer

DD-WRT routers and subnets - how to get devices on same subnet to see each other?

We have an entry point from our ISP. It has the subnet 0, it's a MikroTik device over which we have zero control. We have 2 dumb 4-port switches and 2 wrt54gl routers with DD-WRT installed. These routers have the subnet of 1 by default, as in,…
Swader
  • 499
  • 2
  • 5
  • 18
0
votes
2 answers

Cisco Aironet 1040 and 1260 Migrate from Standalone/Autonomous Mode to Lightweight/Controller-Based Mode

Is there a way to migrate an a Cisco Aironet 1260 and also a Cisco Aironet 1040 both in Standalone/Autonomous Mode to Lightweight/Controller-Based Mode so they can be managed through a Cisco Wireless Controller (Model 2504) or can they be managed in…
CSSNoob
  • 3
  • 2
0
votes
3 answers

WAP + Ethernet Switch Configuration

I need about 20-25 Ethernet connections so I guess a switch is the only way to go. My question is does a wireless access point create a new network (would it make the wireless network a separate network?). I want one network for wireless and wired…
henryaaron
  • 105
  • 4
0
votes
1 answer

Is it possible to put Cisco Aironet 1000 APs in standalone mode?

Almost all of the documentation that I've read seems to suggest that a controller is required, but I've been assigned to sell my employer's old 1000's and finally get rid of the ancient 4400 series controller. Can I reset/unjoin the Aironet APs…
user65712
  • 387
  • 1
  • 8
  • 17
0
votes
1 answer

Cisco Aironet 1200 Access Point Roaming

I have 5 Cisco 1200 Access point. 1 of them is running as WDS and 4 AP is using it. I am using Default Radio Channel: Least Congested Frequency. On the AP running WDS, I can see all 5 APs are registered by: show wlccp wds ap The problem is, in…
jack
  • 1
0
votes
1 answer

Cisco Aironet 1142 reset to default

I have a 1142 that I purchased that needs to be set to factory defaults so that I can configure it. I do an escape at the boot sequence and I get to the ap: prompt, the reset instructions that Cisco provides says that I should rename the old…
rahrahruby
  • 587
  • 6
  • 12
  • 21
0
votes
2 answers

Cisco Aironet 1200 (AIR-AP1231G-A-K9) issues

I bought a Cisco Aironet AIR-AP1231G-A-K9 off of ebay and am having issues with it. The first and most alarming issue is the cycling of the status lights. I read the manual and it does not show that as a possible state. Here is a video of the…
user1080943
  • 31
  • 1
  • 5
0
votes
2 answers

Cisco 881w AP factory reset

If I want to return to the factory IOS and configurations of the AP only, I must issue this command: service-module wlan-ap0 reset default-config right? But which IOS is going to replace the current?
Jonathan Rioux
  • 1,938
  • 6
  • 33
  • 57
0
votes
3 answers

How to get 2.4ghz wifi to work in an area with high interference

I'm having issues getting consistant wifi working in my office. We are in a highly built up area with lots of office blocks around us. I know i should change the channels to e.g. 1,6,11 or something similar but what other options do i have. 2 of the…
user112570
  • 59
  • 4
  • 12
0
votes
1 answer

How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The…
joechip
  • 668
  • 3
  • 6
0
votes
3 answers

Wifi latency?

I'm wondering, is there any wifi latency problems? Like, say this was taken to an extreme though. Like we had a wifi repeater. The repeater consisting of a receiver, which then immediately repeats the signal to an access point, but under a different…
Earlz
  • 1,019
  • 5
  • 13
  • 29
0
votes
2 answers

Setting up private and guest WiFi from Windows Server 2008 R2 for non profit (~20 users)

I'm about to set up a wireless network with a Active Directory domain. The problem is that the desktops they have at the office should connect via AD so they get access to shared resources, gp etc. But they also have frequent guests that just need…
Gabriel Smoljar
  • 101
  • 1
  • 3
0
votes
1 answer

WPA2-Enterprise and RADIUS accounting server

Is mandatory to use WPA2-Enterprise to be able to send accounting packages to my RADIUS server from an access point (Meraki)?
PachinSV
  • 193
  • 1
  • 1
  • 9
1 2 3
…
12 13